Trident Flat Fold P2 Level 3 Respirator Extra Small

Features:

• Multilayer Technology – Advanced multilayer technology providing protection against mechanically and thermally generated particulates including fluids, dusts, mists, fumes, and smoke.
• 3 Panel – Three panel design provides structural integrity, form fit seal, and optimal comfort. All three mask panels and seams have been independently tested and certified to AS 4381:2015 Level 3 – ISO 22609
• Bacterial Filtration Efficiency – Bacteria Filtration Efficiency (BFE) > 99%
• Fluid Resistance – Fluid Protection level 3, 160mmHg
• Proprietary Foam Nose Seal – Proprietary adjustable foam nose pad to ensure consistent optimum facial seal and reduce fogging of eyewear.
• Adapts to Most Faces – Versatile unisex fit suitable for a range of facial shapes and sizes. Effective for many “hard to fit” individuals.
• Fit Test Results – Specialized TRIDENT respirator seal attains unrivalled PortaCount fit testing results.
• Low Breathing Resistance – Low breathing resistance, maximizing wearer comfort, durability, and life of product.
• Use with Other PPE – Designed to be used in conjunction with other mandatory personal protective equipment.
• Latex Free – Latex Free to avoid the risk of developing allergies with repeated exposure.
• Batch Numbered and Individually Packed – Each mask is individually batch numbered and packaged for the ultimate traceability, portability, and hygiene.

Standards & Registrations:

Certified to:

• AS/NZS 1716:2012
• ID No. BMP 732382
• AS 4381: 2015 Level 3, 160 mmHg
• ID No. BMP 737354

ARTG 344154

Packaging:

Sizing:

How to Apply:

• Position the respirator in the palm of your hand with the nose strip at your fingertips, ensuring both head straps are untwisted over the back of your hand.
• Open both the top and bottom panels of the mask and make a bend in the foam nose seal. Place the lower panel under the chin and the upper panel with the foam nose seal over the nose bridge and underneath the eyes.
• Holding the respirator with one hand, position the top untwisted head strap to the crown of the head.
• Draw the lower untwisted head strap up and over the face to below the ears and back of the neck. DO Not Criss Cross Head straps.
• With both hands, mold the foam nose seal at the top of the mask to the nose bridge and cheeks ensuring a secure fit and seal.
• Perform a fit check (see fit check below). Cover the front of the respirator with both hands. Inhale and exhale sharply.

Fit Check List:

• If air leaks at the nose or cheek areas adjust the foam nose seal until a seal is achieved.
• If air leaks around the edge of the respirator adjust the head straps and reposition the mask until a seal is achieved.
• A successful fit check is when there is no air leakage.
• Always fit check before entering the work area.
• If a successful fit check cannot be achieved, remove, and refit the respirator.
• If you still cannot obtain a successful fit check, do not enter the work area.

How to Remove:

• The respirator may be contaminated. Touch only the head straps when removing.
• Pull the bottom strap over the top of the head.
• Pull the top strap over the top of the head.
• Pull the top strap over the top of the head.
• Dispose of respirator into the appropriate waste receptacle in accordance with site infection control and prevention policies.
• Wash and sanitize your hands thoroughly.

Important:

• A fit check must be performed prior to using your disposable respirator.
• Always read the disposable respirator wearer instructions.
• Should air leakage occur around the nose, adjust the foam nose/cheek support strip to eradicate the leakage & perform the above fit check.
• Should air leakage occur around the nose, adjust the foam nose/check support strip to eradicate the leakage & perform the above fit check.
• When an appropriate fit & seal cannot be achieved do not enter the hazardous environment & follow on-site policy referencing AS/NZS 1716:2012.

Note:

To achieve an optimum facial seal, the wearer should be clean-shaven. It is recommended the wearer be fit tested prior to use in accordance with AS/NZS 1715:2009 and/or onsite requirements. Training on the safe use and limitations of the disposable face mask must be performed in accordance with AS/NZS 1715:2009 section 2.4.

More Questions:

Still unsure if this product is right for your intended use? Get in contact with one of our Sales Representatives via the contact us page.